Electrical breakdown service in Brussels : CD Engineering helps you quickly

Firstly, it all depends on the type of electrical installations you have at home. Indeed, the problem will be approached differently depending on the case. So if it is a simple power cut, the problem may come from circuit breakers or fuses. In the first case, you simply need to reset them in your electricity meter. In the second case, you will have to buy new fuses.

If the problem spreads to the whole neighbourhood, you won’t be able to take care of it yourself. In that case, you will need to call an electricity breakdown service in Brussels. Finally, even if the problem is centralised in your home and you think you have solved it, it is best to have the general electricity checked. To do this, you can call us and ask for a free estimate now.

There are three very frequent cases of power failure. The first, unsurprisingly, is a general power cut. This case is quite common, but can be surprising when you don’t expect it. The causes of a blackout are often related to a faulty electrical network or a peak in consumption and connections of electrical appliances. This can cause a short circuit that does not normally affect the state of your electrical system.

The second case is the non-functioning of an electrical appliance. This may be simply due to a failure of the appliance itself, but not only. The problem can also occur due to a faulty plug or a short circuit. In this case, the general condition of the socket and the appliances connected to the same mains supply must be checked. If you can’t find a solution, call in a professional!

Finally, the last case is a lamp that no longer lights up. Obviously, the cause may lie in the need to change the bulb. But not only that. Indeed, the problem may come from further afield. First of all, check the circuit breaker and the switches, they may need to be overhauled! For any electricity troubleshooting in Brussels, call on CD Engineering, your trusted electrician.

There are often many reasons for a power failure. That is why calling an experienced electrician should be your first instinct. In the event of a power surge or overload, you may be in danger. In this case, one of our electricians will come to your home immediately to bring your electrical installations to safety. For less serious cases, we will still intervene within 24 hours.

The 3 main disturbances that occur in an electrical installation are:

• Overcurrents
• Short circuits/surges
• Voltage drops

Overcurrents can be categorised as an overload. For example, if you choose an electric oven that is too powerful for your outlet, this will cause your electrical system to overload, resulting in a long but lasting heat build-up. This will result in the need to troubleshoot the connection of your electric oven. In addition, short-circuits and overvoltages are frequently encountered. Finally, voltage drops can affect your electrical system and cause an electrical problem.

First of all, it is important to know that the origins of overcurrent are generally handling errors. This is why you need the intervention of a technician in Brussels to guarantee your electrical connection. In addition, there are other causes of overcurrent such as faults, which correspond to an incorrect connection of your electrical system. Thus, the electrical charge will pass through any metal element that communicates. Incorrect wiring can cause an overcurrent. So, if the wiring is incorrect, it can lead to short circuits and other problems. Shorts can cause fires, so bad wiring isn’t to be taken lightly.

Il est commun d’utiliser de la même façon les termes surtension et surintensité. Or, une surtension représente une tension trop importante. La surtension peut conduire à la détérioration des appareils électriques. Une surintensité quant à elle représente une intensité trop grande. Elle peut conduire à l’échauffement des conducteurs. Il est important de réaliser une maintenance électrique régulièrement afin d’éviter tout risque d’incendie et de panne.

It is very easy to protect yourself from an overcurrent, the simple use of fuses allows you to protect yourself against overcurrent in your home. There are two types of fuses, the Gg fuse which corresponds to domestic fuses and the AM fuse which is used on machines. The Gg fuse is mainly found in the industrial sector. If you would like more information on the use of fuses, do not hesitate to contact our industrial electrician.

The second way to protect against overcurrent is to install a circuit breaker. There are still two types of circuit breakers. The first type is a circuit breaker which is mainly used in industrial environments to stop the machine in case of problems or accidents. The second type is a differential circuit breaker. Its main role is to protect the circuits in your home against overcurrent and short circuits. It also protects you against fire. It is often placed on the electrical panel.

When you have an electrical overload or short circuit in your electrical installation, the circuit breaker will cut off the power to the circuit where your electrical appliances are connected. In order to reset a circuit breaker you need to go to the electrical panel, it isn’t necessary to call an electrical company to reset it. To locate the circuit breaker that has blown, simply locate the one that is in the down position. Simply turn it up. However, if you pull the handle up and your circuit breaker blows again, then you need to unplug all the appliances on that circuit and plug them back in one by one to locate the problematic appliance.

Everyone can protect themselves from a power surge. This can be done through everyday actions. For example, the simple act of unplugging appliances and electrical equipment when you are not using them. For example, when you have multiple connections to a single electrical outlet through a power strip, it is important to unplug them. You can also install a surge protector on your electricity metre. However, a professional is required to install it.

If you have tried to reset your circuit breaker and it blows again, then there is a problem with your electrical circuit. In order to locate the source of the fault, no detector is needed. Simply unplug the last appliances you plugged in before the circuit breaker went out. If you can’t find the cause of the fault, we encourage you to contact an electrician to ensure that you get a proper electrical repair. A circuit breaker that doesn’t reset may be synonymous with a more serious fault on your circuit. This is why it is necessary to contact CD engineering for your repairs.

For a private individual, it is quite complex to find an insulation fault. Indeed, it is necessary to have an insulation multimeter because the insulation fault is measured. An insulation fault represents a current leakage in an appliance, for example in a dishwasher, between the water and the electrical cables. This measurement shows us the insulation fault or the total insulation fault in case the resistance is infinite. Do not hesitate to call on a CD engineering repairer to find your insulation fault. He will be able to advise you on the work to be done.

There are different ways to detect an electrical problem. First, check whether the problem is widespread in one room or throughout the home. Then check the different electrical installations: the electrical sockets, the electricity meter, the connections, etc. If none of these points seem to be the cause after checking, the problem may be more serious. In this case, it may be necessary to change the entire electrical outlet or even one point in the entire installation. In any case, it is best to hire a technician to repair your electricity in Brussels. The latter not only has the necessary qualifications, but also has the right equipment for this type of intervention.

Finding a faulty contact can be quick, as it’s usually located close to the socket you’ve plugged your appliance into. To remedy the problem, simply change the connection or install a new plug. If you don’t feel comfortable doing the repairs yourself, a qualified CD engineering craftsman can do it for you. After the repair, you’ll be able to enjoy a fully compliant installation. Call us for a free estimate, so there are no surprises on your bill.

In general, most repairs for everyday problems are the responsibility of the tenant. That is to say, when a light bulb breaks, or a fuse, damaged switches, etc., it is the tenant’s responsibility. On the contrary, if it is a problem directly related to the electricity network, the costs will normally be borne by the landlord. The best thing to do, however, is to consult your lease contract. According to the agreements made with the landlord, certain repairs are at your expense as a tenant.

The maintenance of electrical appliances in the house or furnished flat is mainly the responsibility of the tenants. In the event of breakage if the appliances are too old and no longer work, consult your lease contract.

CD Engineering is first and foremost an electrical company that listens to its customers. Indeed, all our employees are passionate electricians for whom the only priority is to ensure the proper functioning of your electrical equipment. This is why we always work with care and in strict compliance with the standards in force in the field of electricity. Moreover, our urgent electrical repair service is among the most efficient in Brussels and Belgium. We can therefore easily diagnose your problem and help you in the best possible way.

In addition to electrical repairs, we can help you with your work. Indeed, for 27 years, we have assisted individuals and professionals in electrical installation work and in the renovation of ageing or obsolete installations. Thus, we do not lack versatility to meet all your needs, whether they are urgent or not. If you have any projects in mind, we can only invite you to contact us by phone today. A qualified electrician will be happy to answer you and provide you with a free estimate.

The execution of an electrical repair depends on the situation. If you already know the source of the problem, our qualified electrician will repair it. He will not need to do any further research to find the type of problem. However, if the cause of your electric boiler repair for example isn’t known. Then your electrician will have to charge you for the fault finding. Moreover, if you want the intervention in the evening or at the weekend, this represents an emergency intervention. The rates will be higher. Thus, the estimates will be different according to the interventions. Do not hesitate to contact us by phone for more information.